Este producto está disponible. Puedes hacer un pedido y lo recibirás acorde al método de envío.
Los productos Bajo Demanda los enviamos a nuestros clientes a través de un pedido.
Haz un pedido normal, nosotros lo pediremos a nuestros proveedores y te lo enviaremos en un solo envío para ahorrar costes.
Actualmente no tenemos stock pero recibiremos pronto. Puedes comprar y haremos el envío tan pronto vuelva a estar disponible (de 1 a 3 semanas).
Pedidos que incluyen productos Bajo Demanda o Back Order serán eviados cuando vuelvan a estar disponibles. Esto significa que el pedido tardará de 1 a 3 semanas en ser enviado una vez el pedido esté hecho y pagado.rnSi deseas recibir primero los productos que si están en stock, por favor realiza dos pedidos diferentes separando los productos en stock, bajo demanda o back order.
Este producto solo está disponible para búsqueda (tutoriales, esquemas...). No pueden ser comprados.
ILIC09341
Nuevo
Advertencia: ¡Últimos artículos en inventario!
Disponible el: 0000-00-00
Display color TFT 320x240
Recipiente :
* Campos obligatorios
total Cancelar
This 320x240 color TFT display is recommended for use with Teensy 3.2, for high resolution color graphics.
It can be used with the Adafruit_ILI9341 library or Optimized ILI9341 library.
ILI9341_t3 supports large high-res fonts. A library of additional fonts is available, as well as huge collection of Google fonts.
Teensy 3.1 and purple test board are not included with this display.
Connections
ILI9341 Pin | Teensy 3.2 Standard | Teensy 3.2 Audio Board | Notes |
---|---|---|---|
VCC | VIN | VIN | Power: 3.6 to 5.5 volts |
GND | GND | GND | |
CS | 10 | 21 | Alternate Pins: 9, 15, 20, 21 |
RESET | +3.3V | +3.3V | |
D/C | 9 | 20 | Alternate Pins: 10, 15, 20, 21 |
SDI (MOSI) | 11 (DOUT) | 7 | |
SCK | 13 (SCK) | 14 | |
LED | VIN | VIN | Use 100 ohm resistor |
SDO (MISO) | 12 (DIN) | 12 |
Caution: Use only 3.3V signals with this display. CS, D/C, SDI, SCK are NOT 5 volt tolerant. We recommend using this display only with Teensy LC & 3.x. It should not be used with 5V boards like Teensy 2.0 and Arduino Uno.
We do not recommend using the SD card socket on this display. It does not work, but this hardware modification may be able to get it working.
Usage With Audio Board Connections
To use the ILI9341 display with the Audio Board, connect the signals using the alternate pins shown above.
For use with the Teensy 3.2 optimized library, use this 6 pin constructor code.
// For optimized ILI9341_t3 library #define TFT_DC 20 #define TFT_CS 21 #define TFT_RST 255 // 255 = unused, connect to 3.3V #define TFT_MOSI 7 #define TFT_SCLK 14 #define TFT_MISO 12 ILI9341_t3 tft = ILI9341_t3(TFT_CS, TFT_DC, TFT_RST, TFT_MOSI, TFT_SCLK, TFT_MISO);
For use with Adafruit's original ILI9341 library, in setup() before calling TFT.begin(), use SPI.setMOSI(7) and SPI.setSCK(14) to configure the SPI library for these alternate pins.
// For Adafruit's ILI9341 library #define TFT_DC 20 #define TFT_CS 21 Adafruit_ILI9341 tft = Adafruit_ILI9341(TFT_CS, TFT_DC); void setup() { SPI.setMOSI(7); SPI.setSCK(14); tft.begin();
Dimensions
The active screen area is approximately 2.8 inches diagonal.
CORZOTECH - EASY LIFE FOR INTERACTION